One of the most coveted words an artist can hear or receive in an email is “invited”
I am so pleased and grateful to have a piece selected. 🙏
Seven cyclist
Hurricane Harvey - sculpture day 19 “bringing home the bacon”
I unclamped the armature from the dolly to load it into my car and........... Houston, we have a problem! The base has warped from the heat of weld on the feet. The base is a basic potato chip. Fixing this is beyond my welding capabilities. This is a job for Blumenthal Sheet Metal. I think if they can weld basically a 2” wide frame around the edge, that would level the edge. It would still bubble in the middle, but that will not matter. I just need an edge that rests on the floor.
I will find out interesting he morning. 🤞
Hurricane Harvey - sculpture day 18 “bringing home the bacon”
I added the man’s thrown back chin, a suggestion of his head shape, and reinforced his wrist and hands. I also added the pig’s tail, reinforced his hoofs, and a added a suggestion of some very big ears.
from the front
From slight left
Left side
The back side
The right side.
Hurricane Harvey - sculpture day 16 “bringing home the bacon”
Hands, hands, hands= frustration
I thought I had a really good plan of attack: draw out a hand the size I want, measure how big each bone should be, cut the bones, and tack them together. Once they are tacked together, bend them into position. This is where the frustration began. Some of the tacks would either not bend or some would break, and I would then have to reweld them. I did finally get them all together. I was mentally exhausted, so I decided to attach them permanently to the arms tomorrow when I am more refreshed.
I did just tack them just to see how they look.
I hope I like them tomorrow.
FYI - I put really big welds on the knuckles because I like knarly fingers with big knuckles. If you deal with livestock, you probably have some pretty banged up fingers. :)
Digits barely tacked together
Left hand gripping Mr. Pig
Right hand gripping Mr. Pig
Both hands
The grip
I am getting close to completing the armature.
Hurricane Harvey - sculpture day 15 “bringing home the bacon”
My day started with an empty tank. I was ready to roll and I had to run refill my argon tank. :(
really irritating
Refilling my Argonne tank.
After lunch I finally got to work. Yesterday, I started the pig’s groin. I figured a pig’s groin looks like a dog’s groin. Not true - I decided to double check, and it turns out pig groins are pudgy and round. Dog groins are more like an empty bowl. It’s good I checked!
Here are images I used for reference. I googled “pig groin” and .....you don’t want to do that. People only post images of pig groins that a Veterinarian should see. I then googled “carrying a pig”. The below image shows how pudgy their grojns are.
Once I lay the lath over the armature, it will look a lot different. It looks weird now. I only put the armature at places that protrude. In the concave places, I will press the lath in. That is why the nose looks bizarre.
I can’t wait until tomorrow to do the hands. :)
Hurricane Harvey - sculpture day 14 “bringing home the bacon”
The tension is starting to build.
For this piece to work I have to be able to show the strain or tension between the man and the pig.
The pig is huge and would have been extremely heavy to pick up. And pigs are not comfortable being carried, he would have been squirming like crazy to pull away from the rescuer.
I added the man’s head outline first. I want his head to thrust back to add to the tension between the man and the pig. Then I added the largest part of the pig's stomach. I need to know where the biggest part is in order to figure out where the man’s arms and hands are going to be gripping the pig. The man's hands will be just above the larges part of the pig gripping it tightly.
Front view
You can now start seeing the tension created with the pull of the man’s head and his arms vs the pigs legs.
Note to self on the head- make the armature on the small side, I can always add plaster to make it larger.
From the back
I still need- pig ears, tail, and to finish the pig’s legs and abdomen. The man needs his head, hands and more definition or volume on the arms.
INSPIRATION-
I am always looking for inspiration to use when sculpting. I follow @mcteams3842 who photographs Navy Seals in training. When I saw the image below I thought of the energy needed to of lift a big pig. I took a screen shot and saved it to my file of photos I look at when working on the piece. I would love to have the rescuer’s head this far back ....... I will have to experiment with it.
I highly recommend @mcteam3842 for amazing photography.
I am thinking of putting a cap on him and loved the brim on the below Navy Seals cap. instagram is a treasure chest of inspiration.
Hurricane Harvey - sculpture day 13 “bringing home the bacon”
Chest, hoofs and dewclaws
Upper chest connected
Hoof and dewclaw
Hoof and dew claw
Hoof and dew claw
Hurricane Harvey - sculpture day 11 “bringing home the bacon”
Today I made and attached the 2-4th legs and 3 hoofs.
View from the front
Left side view
View from the back
Right side view
The legs are only attached by 1 piece of pencil rebar at this point. Once I know exactly what position I want them in I will attach them at 2-3 more locations.
Hurricane Harvey - sculpture day 10 “bringing home the bacon”
Pig nose
Building up the nose tip.
Aerial view
Nose and snout
side view
back view
The other side
Front view- pig nose, snout, back and 1 back leg, clipped to rescuer
Side view of rescuer and part of the pig.
View from the back.
Right side view.
Hurricane Harvey - sculpture day 9 “bringing home the bacon”
Today I adjusted the shoulder width, started the chest and connected the back extensions at the top.
View from the front
View from the back
I might need to trim up his chest tomorrow. Grrrrrr
Hurricane Harvey - sculpture day 8 “bringing home the bacon”
I started the upper torso.
I always make the shoulders too broad and then have to adjust them. I will do that tomorrow.
Hurricane Harvey - sculpture day 7 “bringing home the bacon”
My work day was short today.
Hurricane Harvey - sculpture day 6 “bringing home the bacon”
Hurricane Harvey - sculpture day 5 “bringing home the bacon”
Today I spent a lot of time cutting off and rewelding. The upper leg/booty was too big. After four hours it now has a trimmer.
I am trying to decide if I need to reinforce the lower half of the body or move on. Once I reinforce the joints it is a lot more difficult to make changes. If I move on without reinforcing the welding joints, the piece could fall apart. That is my dilemma.
Hurricane Harvey - sculpture day 4 “bringing home the bacon”
Connecting the legs and reinforcing them.
Building the hips and connecting the legs
Side view
View from back
I create triangles to give the piece stability and strength.
Left side view with triangles
View from the back
view of the right side
Using scraps to create triangles to strengthen the ankles.
Looking back, I can now see the hips are not right and are exaggerating the movement. I will have the movement exaggerated when the piece is finished, but for the armature, I will have to tone it down.
Hurricane Harvey - sculpture day 3 bringing home the bacon
This sculpture is about the movement and the energy of rescuing livestock (a pig) during Hurricane Harvey. Today I have to decide on where the figure's weight needs to be to best balance the sculpture and express the energy of hoisting the swine to safety. The photos I took of Griffin while he was walking helped me committe to the foot placement. For the weight, I need new reference photos taken from each side. I am fortunate that my husband is always agreeable to posing for me. We wrapped a stool in a towel to stand in for the pig. Below are the new photos.
View from the front
View of the left side
back view
Hurricane Harvey - sculpture day 2 “brining home the bacon”
Step one - I find or take a photo to use as a reference. Many times I take screen shots from videos I find online. This time I took photos of Griffin and Alex. At the time I was planning on sculpting “The Guy In the Astros Cap”. I had Griffin carry Alex and I took photos as he walked. I can still use the pictures of Griffin walking. Alex is too cute and tiny to stand in for the pig. I will have to wing the pig.
Photo if Griffin’s feet.
Step 2- I start with the armature for the feet, piecing them together from the small leftover scraps of my last sculpture.
Left foot, right foot
I really like the pigeon toed aspect of this photo.
Even though I like work from photos I feel free to change anything I want.
Gust- patina
November 15, 2018
I am working in the spacious new Glassell Foundry. There is abundance of space to work in.
Hat 👍🏼 Patina👍🏼 Torch👍🏼 Welding gloves👍🏼 Paint brushes👍🏼 Respirator👍🏼 Eye protector👍🏼
The patina I am using is a layered hot patina. First I heat the piece with a torch. Then I start laying a heavy dark brown, then a heavy layer of titanium oxide. About 30 minutes in I spilled the titanium patina.
It is really a bummer because once I remix it I can not use it for 24 hours, the chemicals need to bind together. Grrrrrrrrr.😬
November 19,2018
Starting where I left off.
Three days before thanksgiving and I can’t help myself, I want to finish this patina today.
After a heavy layer of titanium ash I ran out of butane. Luckily a second tank was ready to go.
Faux bois Wedding gift ❤️❤️ #12 the 1st layer on the branches.
You can see the rough coat on the underside of the bench. I am ready for the second application of concrete.
I have flipped the bench over and will work from the top to the bottom. You have to work from the top to the bottom because the process is very messy.
Step 1. Protect the bronze birds by covering them with plastic wrap.
Step 2. Paint the lath with a concrete bonding adhesive.
Step. 3 Make a slip from the concrete and the bonding adhesive. Paint the slip onto the piece.
Step.4 Apply concrete by hand.
Mateo. 5 Remain calm, enjoy the process.
It turns out my bonding adhesive is old, as a result my concrete does not want to stick together. I am grateful I am only working on the scratch coat. I can fix anything that falls off when I apply the final coat.
I like this branch growing around the other
Things did not go as planned as I worked on the bench. My bonding adhesive was old and the cement just was not sticking. And marriages do not go as planned. The lesson here is just roll with it. I will get new bonding adhesive next week and the next application will go smoothly. It is not worth getting upset over. The fun part of marriage is having someone go through the rough spots with you, someone who makes the rough spots not so rough, maybe even fun. Look for the good in every situation, it is there. Make your problems work for you.